Satori WO24P-8 9.5" Egyptian Papyrus Cone Woofer - 8 ohm
Price:
$255.00
The selected item is out of stock, please select a different item or combination
Volume Pricing
10 - 100
10% off
10% off
Overview
Satori WO24P-8 9.5" Egyptian Papyrus Cone Woofer- 242mm- 8 ohm
Satori WO24P-8 9.5" Egyptian Papyrus Cone Woofer- 242mm- 8 ohm
Spec Sheet PDF
Great for moderate-sized vented box (see below).
The Satori range was founded to separate more expensive projects from a wider range of more affordable - but still high-end - SB Acoustics products. “As we get more experience, new materials, better simulation tools, we believe in benefiting the customer with those improvements. We always knew that geometry is essential and we are working more and more with geometry. Every time we get new materials, like beryllium, and we optimize the designs, there’s always room for improvement. We’ve been able to implement significant improvements with beryllium, and we could obtain pretty good results in combination with geometry."
Egyptian Papyrus
Now under the Satori brand are two new 5” and 6.5” midrange drivers, MR13P-4 and MW16PNW-4, respectively, featuring black or natural white cones using Egyptian Papyrus fibers produced in house with a proprietary method, combined with soft low damping rubber surrounds for optimum transient response and low resonance frequency. The cones reveal the natural textures of the papyrus material imported from Egypt, resulting in a distinctive appearance, which will certainly be appreciated for high-end speakers.
For these new Satori drivers, the original ideal was to keep the natural finish of the Papyrus fibers as much as possible, which results in a light brown color. Since Papyrus fibers are not uniform, the cone shows visible spots of different colors which give it a look of a natural “organic” material - but the discussion about potential problems in the market arising from the wrong perception that those were “defects” or signs of an “old” driver, led the design team to also create a black version of the same cone. The fibers are still visible, but for more traditional clients, it might be better accepted.
Some box suggestions:



Spec Sheet PDF
Great for moderate-sized vented box (see below).
The Satori range was founded to separate more expensive projects from a wider range of more affordable - but still high-end - SB Acoustics products. “As we get more experience, new materials, better simulation tools, we believe in benefiting the customer with those improvements. We always knew that geometry is essential and we are working more and more with geometry. Every time we get new materials, like beryllium, and we optimize the designs, there’s always room for improvement. We’ve been able to implement significant improvements with beryllium, and we could obtain pretty good results in combination with geometry."
- Hard paper cone for improved piston operation (made in-house)
- Large optimized ceramic magnet motor system with under-cut pole piece and dual shorting rings
- Vented aerodynamic cast aluminium chassis for optimum strength and low compression
- Soft low damping rubber surround for optimum transient response
- Linear symmetric suspension design for improved dynamic performance
- Non-conducting fibre glass voice coil former for minimum damping
- Long life silver lead wires attached 180° apart for improved stability
- Vented pole piece for reduced compression
- High piston to chassis diameter ratio
- Gasket and bolt hole protrusions for reduced coupling to speaker cabinet
Egyptian Papyrus
Now under the Satori brand are two new 5” and 6.5” midrange drivers, MR13P-4 and MW16PNW-4, respectively, featuring black or natural white cones using Egyptian Papyrus fibers produced in house with a proprietary method, combined with soft low damping rubber surrounds for optimum transient response and low resonance frequency. The cones reveal the natural textures of the papyrus material imported from Egypt, resulting in a distinctive appearance, which will certainly be appreciated for high-end speakers.
For these new Satori drivers, the original ideal was to keep the natural finish of the Papyrus fibers as much as possible, which results in a light brown color. Since Papyrus fibers are not uniform, the cone shows visible spots of different colors which give it a look of a natural “organic” material - but the discussion about potential problems in the market arising from the wrong perception that those were “defects” or signs of an “old” driver, led the design team to also create a black version of the same cone. The fibers are still visible, but for more traditional clients, it might be better accepted.
Some box suggestions:
- Sealed box of 0.8 to 1.2 cubic feet for a 3dB down of about 50Hz
- Vented 1.25 cubic feet with 2" Ø vent by 8" long for f3 of 36Hz
- Vented 1.5 cubic feet with 2" Ø vent by 7" long for f3 of 33Hz
- Vented 1.75 cubic feet with 2" Ø vent by 6" long for f3 of 31Hz
- Vented 2.0 cubic feet with 2" Ø vent by 5" long for f3 of 29Hz



Products You May Like
Scanspeak Discovery 26W/8534G 10" Aluminum Cone Woofer 8 ohm
Product ID: 26w_8534g
Scan-Speak Discovery 26W/8534G 10" Aluminum Cone Woofer -272mm- 8 ohm
Good for moderate sealed box
ScanSpeak Revelator 26W/4867T 10" Woofer Black Aluminum Cone
Product ID: 26W_4867T
ScanSpeak Revelator 26W/4867T 10" Black Aluminum Cone Woofer- 260mm- 4 ohm